Automatic Speed Controller for fans & Coolers
Electronic Schematics > Motor, light and power control > Automatic Speed Controller for fans & Coolers
During summer nights, the temperature is initially quite high. As time passes, the temperature starts dropping. Also, after a person falls asleep, the metabolic rate of one’s body decreases. Thus, initially the fan/cooler needs to be run at full speed. As time passes, one has to get up again and again to adjust the speed of the fan or the cooler.The device presented here makes the fan run at full speed for a predetermined time. The speed is decreased to medium after some time, and to slow later on. After a period of about eight hours, the fan/cooler is switched off.Fig. 1 shows the circuit diagram of the system. IC1 (555) is used as an astable multivibrator to generate clock pulses. The pulses are fed to decade dividers/counters formed by IC2 and IC3. These ICs act as divide-by-10 and divide-by-9 counters, respectively. The values of capacitor C1 and resistors R1 and R2 are so adjusted that the final output of IC3 goes high after about eight hours.The first two outputs of IC3 (Q0 and Q1) are connected (ORed) via diodes D1 and D2 to the base of transistor T1. Initially output Q0 is high and therefore relay RL1 is energised. It remains energised when Q1 becomes high. The method of connecting the gadget to the fan/cooler is given in Figs 3 and 4.
|
|
It can be seen that initially the fan shall get AC supply directly, and so it
shall run at top speed. When output Q2 becomes high and Q1 becomes low, relay
RL1 is turned ‘off’ and relay RL2 is switched ‘on’. The fan gets AC through a
resistance and its speed drops to medium. This continues until output Q4 is high.
When Q4 goes low and Q5 goes high, relay RL2 is switched ‘off’ and relay RL3 is
activated. The fan now runs at low speed.Throughout the process, pin 11 of the
IC is low, so T4 is cut off, thus keeping T5 in saturation and RL4 ‘on’. At the
end of the cycle, when pin 11 (Q9) becomes high, T4 gets saturated and T5 is cut
off. RL4 is switched ‘off’, thus switching ‘off’ the fan/cooler.Using the
circuit described above, the fan shall run at high speed for a comparatively
lesser time when either of Q0 or Q1 output is high. At medium speed, it will run
for a moderate time period when any of three outputs Q2 through Q4 is high,
while at low speed, it will run for a much longer time period when any of the
four outputs Q5 through Q8 is high.If one wishes, one can make the fan run at
the three speeds for an equal amount of time by connecting three decimal decoded
outputs of IC3 to each of the transistors T1 to T3. One can also get more than
three speeds by using an additional relay, transistor, and associated components,
and connecting one or more outputs of IC3 to it.
In the motors used in certain coolers there are separate windings for separate
speeds. Such coolers do not use a rheostat type speed regulator. The method of
connection of this device to such coolers is given in Fig. 4.
The resistors in Figs 2 and 3 are the tapped resistors, similar to those used in
manually controlled fan-speed regulators. Alternatively, wire-wound resistors of
suitable wattage and resistance can be used.
Title: Automatic Speed Controller for fans & Coolers
electronic circuit
Source: www.electronic-circuits-diagrams.com
Published on: 2005-02-01
Reads: 1444
Print version:
Other electronic circuits and schematics from Motor, light and power control
-
Dark-activated LED or Lamp Flasher
-
TRIAC Light Dimmer
-
12 Stage Neon Sequencer (NE-2 / NE-51)
-
PWM Motor/Light Controller
-
Automatic 12 Volt Lamp Fader
-
Auto Heat Limiter for Soldering Iron
-
Triple Stroboscope
-
Simple DC motor PWN speed control
-
Flashy Christmas Lights
-
25 Light Sequencer using Xmas lamps